Home / News / DIY Gelcoat Repair

DIY Gelcoat Repair

Jan 13, 2024Jan 13, 2024

Boat US image

Easy gelcoat repairs

If your boat has a case of dock rash it could be time to think about repairing and refreshing your gelcoat




Masking tape

Plastic sheet



Styrene for thinning (if spraying)

Paper towels

Clean lint-free rags

Compound and polish



Latex or nitrile gloves

Dremel tool with burr-type bit

Mixing sticks

Mixing cups

Plastic spreader

Waterproof abrasive paper in various grits from 120 – 600

Sanding block


About two hours plus curing time.


About $25 for materials.

No matter how careful you are, fiberglass boats collect dings and gouges over time. Many of these are minor and limited to the gelcoat – that smooth, shiny outer layer of the fiberglass layup. Shallow scratches can often be wet sanded and buffed out. But when larger cracks and gouges form, they need to be filled. In most cases, scratches in gelcoat are purely cosmetic and don't affect the underlying integrity of the actual fiberglass, but you’ll still want to address them to prevent moisture from migrating into the laminate as well as to preserve the appearance of the boat.

BoatU.S. has discovered that many owners shy away from gelcoat repairs thinking it's complicated and difficult. But with the correct tools and materials, the right attitude, and a little time, professional-looking repairs are within reach for the average boat owner.

Before getting into the actual repair, it's important to understand what gelcoat is. Gelcoat is the first thing sprayed into a female mold when a boat is built, usually to a thickness of .5 to 1 mm. Depending on the method of construction, layers of chopped mat and fiberglass cloth are then built up on top to form the hull, deck, and other molded parts. When the parts are taken out of the mold, it's the smooth, now outside layer of gelcoat that you see. Gelcoat doesn't fully cure when it's exposed to air, but because one side is against the mold and the other is covered by fiberglass and resin, air is excluded, and the gelcoat cures to form an impervious barrier between the water and laminate.

White is the most popular color for gelcoat, but there are other colors, too. When doing repairs, see if you can buy gelcoat from your boat's manufacturer so you’ll know the color will match. If not, you’ll need to buy white or clear gelcoat and tint it to match. Tinting kits are available from gelcoat suppliers.

Gelcoat is thin, almost like paint, and will run, especially on vertical surfaces. Use several thin coats or use gelcoat paste that is thicker with fewer tendencies to sag. Which type you use will depend on the repair and your method of application. For vertical surfaces, I prefer spray application using several thin coats.

As mentioned, gelcoat has to be sealed from the air for it to harden properly. Otherwise it will stay tacky to the touch. For this reason, you’ll often see "waxed" and "nonwaxed" gelcoat for sale. Gelcoat that has wax added will fully cure; the wax rises to the surface after application, sealing out the air and allowing it to cure. Nonwaxed gelcoat can be used when several coats are required, but that means having two different kinds of gelcoat on hand. The simpler way is to always use the waxed kind, lightly wet-sanding the cured surface between coats.

As with all repairs, preparation is key. Just slapping on some gelcoat will give disappointing results as well as look unsightly, and the repair will probably need to be redone within a year or two. It's better to do it right the first time.

If this is your first time repairing gelcoat, start with a fairly small repair in an inconspicuous place. Gain confidence before moving on to more visible spots on the boat.

Seaglass, my Grand Banks 32, had a small crack in the top of the forward cabin trunk that needed repairing. Here's how I did it.


If you start cutting into the laminates when opening up a crack, you’re going too deep.

Spraying gelcoat

For larger repairs it's possible to spray gelcoat. I’ve had good luck with disposable Preval sprayers available from home stores. These handy devices work just like aerosol cans, except you use them with your own paint or, in this case, gelcoat. You may need to thin the gelcoat a little with some styrene to get it to flow properly.


Protect yourself, especially from dust and fumes. Use common sense, and read and understand all the safety instructions that come with your tools and materials. Catalyst is especially noxious; avoid breathing in the fumes. Wear a respirator, Tyvek suit, and latex or nitrile gloves. If you get gelcoat on your skin, wash it off right away with soap and water. Do not use acetone. – M.C.


Online extra

Visit BoatU.S. YouTube to watch an in-depth webinar with Lenny Rudow on his favorite products, tips, and techniques to keep gelcoat looking great.

This article was reprinted with permission from BoatU.S. Magazine, flagship publication of the membership organization Boat Owners Association of The United States (BoatU.S.). For more expert articles and videos to make your boating, sailing, or fishing better, visit

– M.C.